CLICK HERE TO SEE PRODUCT SHEETS
061825 (ABT1820)
INTERNAL CUSTOMER LEAD IN KIT (CLI)
This is used to cover, control and protect the fibre optic cable where it emerges inside the premises. This would typically be used where the customer box is either outside the premises or not directly opposite where the cable comes through the wall from outside.
The kit consists of:
1 x CLI with 15mm Bend Radius
1 x Internal Cover (White)
1 x 300mm Conduit
1 x CSP Connector
061826 (ABT1830)
EXTERNAL CUSTOMER LEAD IN KIT (CLI)
This is used to cover, control and protect the fibre optic cable on the outside of the premises as it goes through the wall and connects to the customer box inside the premises.
The kit consists of:
1 x CLI with 15mm Bend Radius
1 x External Cover (Grey)
(ABT1860)
CUSTOMER LEAD IN KIT (INTERNAL & EXTERNAL)
This is used to cover, control and protect the fibre optic cable on both sides of the wall. This would typically be used where the customer box is not directly opposite where the cable comes through the wall from outside.
The kit consists of:
2 x CLI with 15mm Bend Radius
1 x Internal Cover (White)
1 x External Cover (Grey)
1 x 300mm Conduit
061827 (FTE0700)
CUSTOMER LEAD IN KIT THICK WALL
This is used in situations where the wall is thicker than 300mm.
The kit consists of:
1 x 500mm Conduit
069581 (ABT1890)
BLOWN FIBRE EXTERNAL CUSTOMER LEAD IN WITH OH ADAPTOR
This is a cable entry cover with a 30mm bend radius to allow blowing of the fibre after installation. It includes space for captive gas block and can be used with cable sizes up to 6mm. The kit includes an overhead adaptor for use with overhead cables and fits onto the Capping 25A or Connector Bend No.4 when connecting to underground ducting as shown in the photo below. It can be used in conjunction with the Blown fibre Internal CLI ABT1900.
The kit consists of:
1 x External CLI base
1 x External CLI Cover
1 x Overhead Adaptor
069582 (ABT1900)
BLOWN FIBRE INTERNAL CUSTOMER LEAD IN BASE & COVER
This is an internal cable entry cover with a 30mm bend radius to allow blowing of the fibre after installation. It can be used with cable sizes up to 6mm and can be used in conjuction with the Blown fibre External CLI ABT1890. The picture below shows the Internal CLI being used with FTE0710 ‘D’ Tube Internal capping white and an interface with the customer splicing point.
The kit consists of:
1 x Internal CLI base
1 x Internal CLI Cover
(FTE0710)
‘D’ TUBE INTERNAL CAPPING WHITE
This is for protecting the cabling from the cable entry cover to the customer box. It can be used in conjunction with ABT1920 Blown Fibre 90 degree bend kit.
69584 (ABT1920)
BLOWN FIBRE 90 DEGREE BEND KIT
This is for protecting the cabling and maintaining the bend radius around 90 degree bends for use when the entry through the wall is not directly in line with the customer box. It is used in conjunction with FTE0710 ‘D’ Tube Internal capping white.
69583 (ABT1910)
BLOWN FIBRE INTERNAL DUCT COVER & TUBE
This is used when the cable entry is from under the floor inside the building. The duct cover is designed to cover skirting board and can be trimmed to suit most sizes and designs. This product can be used in conjunction with ABT1920 Blown Fibre 90 degree bend kit where the entry through the floor is not in line with the customer splicing point.
The kit consists of:
1 x Internal Duct Cover
1 x ‘D’ Tube Internal Capping White
1 x Internal Customer Splicing Point Interface
BLOWN FIBRE EXTERNAL CUSTOMER LEAD IN & TUBE
This is an external cable entry cover with a 30mm bend radius to allow blowing of the fibre after installation. It is for use when a gas block is not required at the customer entry point. It can be used with cable sizes up to 6mm and can be used in conjuction with the Connector Bend No.4
The kit consists of:
1 x Connector Bend Convertor
1 x ‘D’ Tube Internal Capping Grey
1 x External CLI Mini Cover Grey
1 x External CLI Mini Base Grey
072180 (FBT0131 – 50)
Capping 25
For use with Connector Bend No.4 to extend up the wall. It can connect to ABT1890 Blown Fibre External CLI, the cover 101A or an External CSP.
095096 (FBT0321)
CONNECTOR BEND 4
For use on housing estates or where the cables emerge from underground. It can be used with to connect with Duct 102 or Duct 56. It can connect to variety of solutions including, Blown Fibre CLI (with and without gas block), Cover 101A or an External CSP
Blown Fibre Drop Manifold
057773 (ABT1780)
UNDER GROUND BLOWN FIBRE TUBE MANIFOLD 1A
Blown fibre drop 12 Way Manifold from 4mm Tube to 6mm for use underground.
057772 (ABT1790)
OVER GROUND BLOWN FIBRE TUBE MANIFOLD 1A
Blown fibre drop 12 Way Manifold from 4mm Tube to 6mm for use over ground (including Pole Mounting Bracket)
057971 (ABT1800)
BLOWN FIBRE TUBE IN-LINE JOINT
Blown fibre drop 12 Way In-line Joint from 4mm to 4mm tube for use underground
UNIVERSAL FIBRE TUBE IN-LINE JOINT
Underground or Overhead enclosure for connecting blown fibre tubes. Suitable for most sizes from 3mm – 10mm.
055175 (FBT0880)
BLOWN FIBRE TUBE BRACKET 1A
For attaching the BFD manifold to the pole for use over ground
(CKT045)
SET OF 12 COLOURED CAPS FOR FTTP BFD MANIFOLD
Spare coloured caps for the BFD manifold
(NC2627)
PLUG REMOVAL TOOL
Spare coloured caps for the BFD manifold
